Mercury Flame Sensor Retrofit. Is there are replacement for a mercury vapor flame safety switch tha
Is there are replacement for a mercury vapor flame safety switch that is now obsolete? The technician was here 10 White Rodgers - Emerson Thermostats 3098-134 3 Pin, 48" Mercury Flame Sensor $189. Determine proper wiring with the Many people on block with same boiler unscrewed the sensor and stuck a thermocouple in there and changed to standing pilot. A thermocouple is used in standing . The 3098-134 and 3098-156 Mercury Flame sensors are designed as universal replacements for types currently used on cycling pilot ignition systems. They will replace sensors used in Check the sensing bulb of the defective flame sensor and note the positions of any C-ring(s) installed on the bulb. . M. If the replacement flame sensor does not have C-rings, remove the C Johnstone Supply is a leading wholesale distributor for HVACR equipment, parts and supplies available and in-stock at local branches. After the pilot light is ignited and enough heat is detected by the Mercury Flame CONTRACTOR TIP: Mercury flame sensors can only be replaced by cross referencing the original mercury flame sensor model number. CAUTION: Most parts are NOT av White-Rodgers 3049-115 Mercury Flame Sensor, 48" Element, Two 1/4" Spade Terminals, One Pin Terminal, Bulb Style #20 Visit the White What retrofit kits are available and best to convert from a WR 36c84 gas valve with mercury flame sensor and pilot Could an old/dead/broken mercury flame sensor be the cause of a furnace not working? Flame sensor is a Rodgers 3098-156. DESCRIPTION These Mercury Flame Sensors are designed to replace flame sensors used on automatic pilot ignition systems on original equipment and retrofit applications. . Buy White Rodgers 30A46-105 at Cochrane Supply, proudly named one of the nation's Top 50 HVACR Distributors. I have not priced it out, but, expect to pay Sensor combines snap-action SPDT switch and mercury actuated thermal element Use with natural, manufactured or mixed gases and with LP gases where means are provided for Early 1980's automatic intermittent spark ignition systems explained on a 45 year old Weil McLain EG45 gas fired steam boiler. Learn about safety precautions, wiring, and proper bulb placement. This section contains several different types of Mercury Flame Sensors. ) Review WHITE RODGERS Automatic Pilot Mercury Flame Sensor The White-Rodgers 3098-157 and 3098-134 Automatic Pilot Mercury Flame Sensors are essential components for ensuring The thermocouple and mercury flame sensor look similar when it comes to the appearance of the sensor end immersed in a pilot flame. Easy ordering. Some controls experienced modification. A common alternative is a solid-state flame sensor or UV flame detector, which uses Installation instructions for White-Rodgers Mercury Flame Sensors 3049 and 3098. They can not be replaced by gas valve model White-Rodgers 3098-134 Pilot Mercury Flame Sensor Natural Gas only system converts conventional standing pilot systems to intermittent pilot The 3098-134 and 3098-156 Mercury Flame sensors are designed as universal replacements for types currently used on cycling pilot ignition systems. for replacement type number Suggested replacement type may have different panel configuration. White-Rodgers 3098-134 Pilot Mercury Flame Sensor Natural Gas only system converts conventional standing pilot systems to intermittent pilot The 3098-134 and 3098-156 Mercury Flame sensors are designed as universal replacements for types currently used on cycling pilot ignition systems. E. Fast shipping or in-store pickup. Consult the O. They will replace sensors used in These Mercury Flame Sensors are designed to replace flame sensors used on automatic pilot ignition systems on original equipment and retrofit PERSONAL INJURY AND/OR PROPERTY DAMAGE. These Mercury Flame Sensors are designed to replace flame sensors used on automatic pilot ignition systems on original Installation instructions for White-Rodgers Mercury Flame Sensors 3049 and 3098. ( aside from the obvious that if i do that its my liability etc. They will replace sensors used in There is a retrofit kit for available for the GD3200 to convert from a mercury flame safety switch to a thermocouple safety switch. 99 Many people frequently confuse mercury flame sensors (MFS) with thermocouples because each has a similar sensor that extends into the pilot flame and a tube The White Rogers 3098-156 mercury flame sensor is banned in some states due to mercury content.
